OddWorks
patreon
PLASMA CUTTER IS COMPLETE!!!!
🕑 Added 2023-11-30 17:44:04 +0000 UTCHELLO EVERYONE!!!! today I’m excited to let you guys know, THE PLASMA CUTTER! IS COMPLETE!!!! woooohoooo! this project has been one hell of a test and pushed me to the limits! so much so that for this model I come up with a completely new electronics set-up to make this model work! :D
about that! last time I posted about this model, the Pico's where burning out thanks to the power draw from the servos! not great! to fix this grabbed a Pico servo board! this board you pop the Pico on and it provides break out pins for the parts as well as a convenient way to power everything, also no more blowing up Pico's!!! woohoo!
but then I ran into another issue! the 18650 power suplly i normally use would not work! the 18650 board that holds the batterys only provides around 1 amp and if it senses more draw than that it shuts down. not good! but there was a fix!!! just use AA batteries!! :D Thanks to the Pico servo board a lot of the power regulating components that were on the 18650 board are on the servo board making it redundant and AA provide all the power needed :D wooohooo
after all that!! the servos finely worked!!! and the model was able to transform!!!!! woooohoooo!!!
TO THE FEATURES!!!
this model has!
bolt-together construction!
lighting up barrels!
removable mag!
ammo counter! designed to emulate the health bar on Clarke’s back!
dual trigger! pull halfway to fire, pull fully to transform the model!
and the big one!!! THE ELECTRONICS!!!
pop open the battery box and power on the model, it does its start up sequence :D (watch your hands around those moving plates! hehe) after its finished the plats with open and the barrels will light up! pull that trigger and the barrels will flash as they fire! the ammo bar will then deplete! getting dimmer and eventually turning red :D the ammo is empty the model will go into a shutdown state, you will need to remove the mag from the top and reinsert it! the model will then go back into the firing state! and the big party trick!! pull the trigger fully in and the model with transform!!! the will open up fully and the entire barrel assembly will rotate 90 degrees!! :D Cool side note the barrels will also change their length in the transformed state :D pull the trigger again and the model will transform back!!!
this model pushed me past my limits and came so close to having the transform feature scraped! but thankfully it worked!!! and thanks to this model I have a new electronics package that works for models needing a bit more torque!!!! :D
just wanted to say thank you so much, I think this model more than any other model I have done exists thanks to you guys :D YOU ARE AWESOME!!!! :D
you can find the model here :D HAPPY PRINTING :D
https://www.patreon.com/posts/93826976?pr=true
Comments
Cobalt Showboat
An incredible accomplishment! Well done!
OddWorks
thank you so much man :D this one was nuts :D but worth it! hahaha Im allready thinking about models that could use this new electronics set up hahaha :D
OddWorks
thank you so much! :D This one was tough but was worth it! :D
OddWorks
thank you so much! This one was a challenge! but so worth it! I can’t wait to paint it up :D oh on that!!!! this model wiring is easier thanks to the servo board :D thanks to its headers all that is needed is to attach depont connectors to the wires and plug in everything :D
OddWorks
hahahaha hell yeah!!!! HAPPY PRINTING :D
OddWorks
Thanks so much man! this one is special :D now to tear it down for painting :D
OddWorks
woooohooooo! awesome!! im glad you like the model man! happy printing! :D
Ryan
Oh, WOW! 🤯
Carter Avery
awesome man im always happy to wait on your models. I gotta say I am a civil engineer so the wiring is not easy for me lol but I'm going to really try hard on this one.
maxwellB207
WOOOO Let's goooooooo
Spartan 052
This is INSANITY! Very impressive
Maces_Armoury
That is absolutely amazing work!
Joe Maletta
Beyond excited for this one! Thank you for the work you put into this. Love your work.
